LANDROVER Diagnostic Software for X-431 Series
Date：
2017-09-30
Clicks:
183
Compared with the previous version:
1. New functions
1) Related Data Stream
2) Added functions Fuel Prime Routine
3) Calibrate Dynamic Volume Control
4) Oxidation Catalyst
5) Oxygen Sensor
6) Seat Cushion Replacement
7) Transfer Case Control Module Reset – Clear
8) Door Window Calibration
9) Driver's Seat Calibration
10) Door Glass Window Calibration
11) Set Air Suspension Control Module Manufacturing/Freeze Mode
12) Set Air Suspension Geometry
13) Set Air Suspension Tight Tolerance Mode (Headlamp Setting)
14) Stepper Motor Initialisation
15) Throttle Valve Actuator
16) Engine Control Module Mass Air Flow Adaption Clear
17) Engine Control Module Low Pressure EGR Adaption Clear
18) Injector Replacement
19) Tire Pressure Sensor Replacement
20) Tire Pressure Monitor Sensor Identification Display
21) Added function Air suspension calibration,
22) Air suspension deflation
23) Air suspension inflation
24) Air suspension pre-geometry
25) Air suspension transportation/customer mode
26) Brake sensor set-up
27) Electric parking brake clutch calibration
28) Particle filter regeneration
29) Reset the diesel particulate filter stored values
30) Oil service counter reset
31) Front axle sensor and/or rear axle sensor
32) Right headlamp and/or left headlamp
33) Steering column calibration
34) Engine fuel priming routine
35) Fuel burn heater - fuel prime application
36) Fuel burn heater - operation check
37) Fuel burning heater – fuel priming routine
38) Fuel prime routine
39) Idle speed control
40) OBDII readiness tests
41) Petrol engine control module adaption clear
42) Purge valve self test
43) Transmission control module adaptation clear
44) Immobilization set-up
45) Evaporative system leak check
46) High pressure fuel pump replacement reset
47) Lambda sensor gain adjustment reset
48) Injector replacement resets
49) Exhaust gas recirculation valve replacement reset
50) Turbocharger replacement reset
51) Mass air flow sensor replacement reset
52) Diesel particulate filter pressure sensor replacement reset
53) Ignition cycle counter reset
54) Reset compressor protection counter
55) Reset water in fuel detection
56) Reset selective catalyst reduction quality monitor
57) Reset selective catalyst reduction start inhibit
58) Parking aid control module reset configuration state.
59) Speed control alignment
60) Activate telematics control module
61) Activate glow plug control
62) ABS configuration clear
63) Calibration learn
64) Absolute position sensor replacement
65) Activate test picture
66) Telematics control module battery replacement reset
67) Roof blind Calibration
68) Service mode disabled
69) System flush
70) High oil temperature reset
71) Battery replacement
72) Head up display control module reset
73) Parking aid control module reset
74) Oil change reset
75) ABS control module configuration clear
76) Configure new ABS control module or steering angle sensor calibration
77) Oil dilution reset
78) Oil service counter level
79) Seat calibration
80) Seat cushion replacement
81) Service interval reset
82) Transmission control module adaptation clear
83) Transmission control module clear oil degradation counter
84) Transmission control module clear self-learning data
85) Transmission control module neutral learn
86) Steering angle sensor calibration
87) Display injector correction factors
88) Injector cycle test
89) Injector leak back test
90) Inlet metering valve
91) Reset the diesel particulate filter stored values
92) Clear lost keyfob transmitters
93) Last alarm activations
94) Program additional transponders
95) Program new keyfob transmitters
96) Program new transponders
97) Passenger's side - Door glass window calibration
98) Driver's side - Door glass window calibration
99) Steering column lock module
100) ECU version information for the model XJ(2002-2009), S-TYPE(1999-2008), X-TYPE(2001-2008), XK(2003-2006)
2. Optimized functions
1) Optimized Automatically Search Function
3. Fixed bugs
None